A car alarm and the keyless entry system can do more than saving money on your car insurance and increase the value of your car since they are important safety features. A car alarms can prevent thieves from stealing your vehicle, hence it is highly valuable while a keyless entry system can help quickly enter your car in a parking without any worries. If your vehicle does not come with a car alarm and remote entry system, you can install these devices yourself. This work requires experience in automotive wiring, however.
The Installation Process
Step 1
Acquire the wiring diagram of the vehicle to determine the codes and colors for locations of vehicle wiring. Find out the type of door lock system and determine the correct relay door lock wire procedure.
Step 2
Using the diagram, you can assess which cables to keep and which to remove. For example, find an unused channel and shorten the cable about six inches long. Use duct tape to mount clipped to the main harness cords and use duct tape to pack the rest of the wiring. Leave four inches exposed wire for each connection end.
Step 3
See the wiring diagram to find the wire feed head coach, ignition cables, cable boot, and position of light cables. With a knife, remove a small portion of the vinyl covering of the cables connected to cables of keyless entry. Use wire strippers to strip the ends of the main power cables, grounding, power switch and parking lights. Connect the ends of these cables with keyless entry cables. Connect the black side of the ground wire to the vehicle chassis.
Step 4
Using the wiring diagram, determine which system locks the door that comes with the vehicle. Directly connect keyless entry cables to the vehicle wiring system if there is a negative closing door installed. Carefully, connect two relays of 30 amp wire and secure the ends of the wires of the vehicle if there is a positive locking system of doors or five-wire system of reverse door lock installed.
Step 5
Connect the main circuit board of the keyless entry into the harness. Test to see if the locks and parking lights work. Using an electric drill and a 3/8 inch, install the LED on the board.
You can replace the remote starter in your 1996 Chevy Cavalier which is made from the top of the engine compartment, making the work faster and accomplish in a shorter period. You can do this work on your own and it will save you a bill of major repair. The starter replacement for the Cavalier is available at the Chevy dealer or through any auto parts store. The starter is in the front of the engine, which is very easily accessible, but be careful and ensure that you do not to damage the radiator while working around the front of your car.
Instructions for Installation
You need to follow the steps mentioned below in order to install the car starter in your 1996 Chevy Cavalier.
- In the first place, find the end of the negative battery cable of your Cavalier. Loosen the retaining bolt from the cable end with a wrench and then remove the battery cable and insulate the battery cable while working on the starter.
- Locate the starter from the front of the vehicle and the engine compartment and remove the wiring harness connector to the ‘S’ terminal with a wrench and push wires aside. Now you have to locate the battery cable to the car starter. As soon as you find it, remove the battery cable terminal on the starter with a wrench ‘B’ and push this cable on one side as well.
- Now remove the two mounting bolts of starter with a socket and ratchet and then slide the starter out of the hole in the cover of the hood. Lift the starter out of the engine compartment and set it aside.
- Get a new starter in the engine compartment and slide the nose cone on the starter in the hole in the cover of the hood. Install the two mounting bolts on the new starter and tighten to 66 ft-lbs with a torque wrench.
- Install the battery cable to the terminal ‘B’. Install the retaining nut and tighten with a wrench. Plug the wiring harness in the ‘S’ terminal of the solenoid. Now make sure that the attachment tabs snap into the place.
- Install the end of the negative battery cable to the battery terminal and tighten the screw with a wrench.
You are done with the installation process of starter in 1996 Chevrolet Cavalier. If you want to install a remote starter, I suggest you to visit thereviewgurus to better options in this regard.